Creating content lists, the basic commands Creating content lists in LaTeX documents is straight forward. Typing these three commands is sufficient to produce a toc, lof, and lot. To produce the lists, the document has to be typeset twice.
But if you make manual styling changes to your heading, for example a very long title, or some special line-breaks or unusual font-play, this would appear in the Table of Contents as well, which you almost certainly don't want.
LaTeX allows you to give an optional extra version of the heading text which only gets used in the Table of Contents and any running heads, if they are in effect. This optional alternative heading goes in [square brackets] before the curly braces: You can change the depth to which section numbering occurs, so you can turn it off selectively.
By default it is set to 3. If you only want parts, chapters, and sections numbered, not subsections or subsubsections etc. For example, if you want to change it to "1": It can be reset in exactly the same way as secnumdepth. If you want the unnumbered section to be in the table of contents anyway, use package unnumberedtotoc .
KOMA classes provide those commands by default.
Simply type the text and leave a Latex thesis abstract line between paragraphs. The blank line means "start a new paragraph here": For formatting paragraph indents and spacing between paragraphs, refer to the Paragraph Formatting section.
Table of contents[ edit ] All auto-numbered headings get entered in the Table of Contents ToC automatically. Entries for the ToC are recorded each time you process your document, and reproduced the next time you process it, so you need to re-run LaTeX one extra time to ensure that all ToC pagenumber references are correctly calculated.
We've already seen how to use the optional argument to the sectioning commands to add text to the ToC which is slightly different from the one printed in the body of the document. It is also possible to add extra lines to the ToC, to force extra or unnumbered section headings to be included.
For example if you use an unnumbered section heading command to start a preliminary piece of text like a Foreword or Preface, you can write: You can use the same mechanism to add lines to the List of Figures or List of Tables by substituting lof or lot for toc.
Depth[ edit ] The default ToC will list headings of level 3 and above. To change how deep the table of contents displays automatically the following command can be used in the preamble: The levels are defined above on this page.
Note that this solution does not permit changing the depth dynamically. You can change the depth of specific section type, which could be useful for PDF bookmarks if you are using the hyperref package: Book structure[ edit ] The standard LaTeX book class follows the same layout described above with some additions.
By default a book will be two-sided, i. Furthermore current chapter and section will be printed in the header. If you do not make use of chapters, it is barely useful to use the book class. Additionally the class provides macros to change the formatting of some places of the document.
We will give you some advice on how to use them properly. Page numbers will be printed in roman numerals.
Frontmatter is not supposed to have sections, so they will be numbered 0. Check the Counters chapter for a fix. The mainmatter chapters works as usual. The command resets the page numbering. Page numbers will be printed in arabic numerals.
Appendices can be used for the article class too: The backmatter behaves like the frontmatter. It has the same issue with section numbering. As a general rule you should avoid mixing the command order.
Nonetheless all commands are optional, so you might consider using only a few. Note that the special content like the table of contents is considered as an unnumbered chapter.
This is one traditional page order for books.Zoo history. Dissertation on zoo exhibit design in Singapore Zoo written by Michael Graetz for a Master of Architecture degree from National University of Singapore.
Design For Life Consultancy was established in by Michael Graetz. In a subsequent phase, an expanding community abstract thesis latex template of artists in a small space without sacricing either.
It means, in short, makes it clear in relation to material resources, to information on monday, do it. I wrote a somewhat short post on list of figures and list of tables a few years ago. Nevertheless, it gets quite a bit of traffic, possibly due to the large number of comments.
For that reason, I decided to put together another, more informative post on the same topic that includes table of contents. TeX - LaTeX Stack Exchange is a question and answer site for users of TeX, LaTeX, ConTeXt, and related typesetting systems. How to write abstract and acknowledgement in book format?
Ask Question. up vote 13 down vote favorite. 6. I need to use this: Abstract for thesis. Related. TeX - LaTeX Stack Exchange is a question and answer site for users of TeX, LaTeX, ConTeXt, and related typesetting systems. Inserting abstract into book document.
Ask Question. Abstract for thesis.
Related. Which package is best/easiest for a TeX newbie to lay out a book for print? The infinity symbol ∞ (sometimes called the lemniscate) is a mathematical symbol representing the concept of regardbouddhiste.com symbol is encoded in Unicode at U+E ∞ infinity (HTML · ∞) and in LaTeX as \infty..
It was introduced in by John Wallis, and, since its introduction, has also been used outside mathematics in .